Products
HomepageProducts
PLAMOSTOP P9 is a water-based fire protective intumescent coating material.
SSpecial one-component middle-layer coat for fire protection of steel construction in the enviroment type "Y" - indoor enviroment and partial exposure. Possible use only in the VitoFire V1-V4 systems certified for the EU corresponding to ETAG 018. The film thickness of Plamostop P9 is neccessary to calculate particularly for every object. It is also used to increase the fire resistance of reinforced concrete structures, based on the determination of the concrete thickness equivalent to increasethe tension of reinforcement, calculated according to the dimension table. It can be applied by a roller, brush or airless-spraying. Applicable only by a trained person possesing a valid certificate. Appropriate priming coats: KG 13 or ZG 13, finishing coats: KD 53, PD 53, HAE 30 for reinforced concrete structures.
| Segment: | water-born |
|---|
| Substrate: | steel with old coating, new steel - mechanically cleaned, new steel - manually cleaned |
|---|
| Usage: | special |
|---|
Technical data sheet
Safety data sheet
TIXODECOR is a gel aroma-free lasure with UV filter for wood.
High quality non-sagging thin film gel lasure with UV filter based on oil. Used for wooden cottages, pergolas, arbours,
summerhouses, fences, ceilings, staircase, casing frames, balks and garden furniture. Contains fungicidal agents, protects against
mold, funghi and wood blueing. Suitable for new uncoated wood or for renovation of old coatings. Lasure is possible to use as a
wood penetration coating before application of colourless varnish. This is recommended especially for strained surfaces such as
staircases, floors, tables and furniture or paneling.
| Substrate: | wood |
|---|
| Usage: | glazing |
|---|
Technical data sheet
Safety data sheet
environmentally friendly cleaner, degreaser and stripper
Used for cleaning application equipment, cleaning wet or dry waterborne paints drips, degreasing surfaces before application of any type of paint and removal of old paint, dip for long enough. Applying by the a spray-gun, a brush or a towel. After short effect of CL 07, the surface must be wiped with a clean and dry towel. Depending in the degree of grease use a new towel. After use CL 07 rinse the surface with clean water! Do not use to adjust the viscosity of paints. CL 07 does not contain either acids or alkalies.
Technical data sheet
Safety data sheet
Roof, facade, paving and wood cleaner
Designed to clean and remove blue and green stains along with other contamination from paving, masonry, bricks, concrete, gypsum, limestone, granite, sandstone, all types of roofing and wood. When treating the surface with CL 71 concentrate, the surface is protected from re-contamination for 10 years. The use of CL 71 is safe and has no negative impact on building materials.
| Segment: | special |
|---|
| Usage: | special |
|---|
Technical data sheet
Safety data sheet
thinner for nitrocellulose coating materials.
C6000 is intended for the viscosity adjustment of coating materials VITON if necessary accelerate the drying time, typically during application the paint at low temperature or during application the paint on small and rugged surfaces. The quantity of thinner depends on the chosen type of application, on the temperature and on the type of chosen paint. The maximal quantity is specified in the technical data sheet of the particular paint. Mentioned thinner is intended only for coating materials and paints by VITON s.r.o. When applying a VITON paint combined with a thinner by another manufacturer the paint guarantee expires.
Technical data sheet
Safety data sheet
Thinner for polyurethane and acrylic coating materials.
PT 03 is intended to adjust the viscosity of VITON paints applied by a spray gun, a brush or a roller. The quantity of thinner depends on the chosen type of application, on the temperature and on the type of chosen paint. The maximal quantity is specified in the technical data sheet of the particular paint. Mentioned thinner is intended only for coating materials and paints by VITON s.r.o. When applying a VITON paint combined with a thinner by another manufacturer the paint guarantee expires.
Technical data sheet
Safety data sheet
Thinner for extending the drying time of 2K polyurethane and 1K acrylic coating materials
It is designed to adjust the viscosity of 2K polyurethane and 1K acrylic VITON coatings in cases where it is necessary to extend the drying time. This is most often the case when the coating is applied at elevated temperatures or on large flat surfaces. The amount of thinner required depends primarily on the type of application equipment, the application temperature and the type of paint being thinned. The maximum thinner dosage is specified in the technical data sheet of the intended coating. This thinner is specially developed for coatings and paints of the company VITON s.r.o.
Technical data sheet
Safety data sheet
thinner for synthetic coating materials applied by spraying.
KT 01 is intended to adjust the viscosity of VITON paints applied by a spray gun. The quantity of thinner depends on the chosen type of application, on the temperature and on the type of chosen paint. The maximal quantity is specified in the technical data sheet of the particular paint. Mentioned thinner is intended only for coating materials and paints by VITON s.r.o. When applying a VITON paint combined with a thinner by another manufacturer the paint guarantee expires.
Technical data sheet
Safety data sheet
Thinner for extending the drying time of synthetic coating materials
It is designed to adjust the viscosity of VITON coatings in cases where it is necessary to extend the drying time. This is most often the case when the coating is applied at elevated temperatures or on large flat surfaces. The amount of thinner required depends primarily on the type of application equipment, the application temperature and the type of paint being thinned. The maximum thinner dosage is specified in the technical data sheet of the intended coating. This thinner is specially developed for coatings and paints of the company VITON s.r.o.
Technical data sheet
Safety data sheet
fast recoatable thinner for synthetic coating materials.
KT 04 is intended for the viscosity adjustment of coating materials VITON if necessary to apply more layers in a short time interval. The quantity of thinner depends on the chosen type of application, on the temperature and on the type of chosen paint. The maximal quantity is specified in the technical data sheet of the particular paint. Mentioned thinner is intended only for coating materials and paints by VITON s.r.o. When applying a VITON paint combined with a thinner by another manufacturer the paint guarantee expires.
Technical data sheet
Safety data sheet
Universal thinner for synthetic coating materials
It is designed to adjust the viscosity of VITON coatings applied by spray gun, brush, or roller. The amount of thinner required depends primarily on the type of application equipment, the application temperature, and the type of paint being thinned. The maximum thinner dosage is specified in the technical data sheet of the intended coating. This thinner is specially developed for coatings and paints of the company VITON s.r.o.
Technical data sheet
Safety data sheet
thinner for epoxy coating materials.
ZT 03 is intended to adjust the viscosity of VITON paints applied by a spray gun, a brush or a roller. The quantity of thinner depends on the chosen type of application, on the temperature and on the type of chosen paint. The maximal quantity is specified in the technical data sheet of the particular paint. Mentioned thinner is intended only for coating materials and paints by VITON s.r.o. When applying a VITON paint combined with a thinner by another manufacturer the paint guarantee expires.
Technical data sheet
Safety data sheet
English 
Česky
Deutsch